Shopping cart - Cart Subtotal:$0.00

 
 
 

BeagleBone Capes

The capes listed below are compatible with BeagleBone (White).

   

Set Ascending Direction
per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4
  1. BEAGLEBONE LCD7 CAPE

    BEAGLEBONE LCD7 CAPE

    $157.95



    The BeagleBone LCD7 cape provides an LCD solution with touchscreen capability for BeagleBone boards. The 7" TFT LCD screen, attached to the topside of the board, can display up to a resolution of 800x480 and is a 4-wire resistive touchscreen. The board is equipped with seven buttons located at finger-friendly positions. These buttons include five user buttons that are connected to GPIO signals as well as power and reset. The backside of the cape is where the BeagleBone and additional cape can be mounted.

    Note: Compatible with BeagleBone Black (RevA2 only supports booting from microSD card, RevA3 or newer is fully supported when using Angstrom release 2013-06-20 or newer). Please visit the Software Support section on the wiki page for more details.

    Learn More
  2. BEAGLEBONE TIWI-5E CAPE W/ EXTERNAL ANTENNA

    BEAGLEBONE TIWI-5E CAPE W/ EXTERNAL ANTENNA

    $68.95

    Out of stock

    The BeagleBone TiWi-5E Cape w/ External Antenna is an add-on board that provides Wi-Fi capability for the BeagleBone. This cape is equipped with LSR TiWi-5E module that is capable of providing high performance 2.4 GHz and 5 GHz IEEE 802.11 a/b/g/n. The TiWi-5E chip use on this cape is based on the Texas Instrument WL1273L chipset. This cape uses an external antenna.

    Note: Hardware incompatible and will damage BeagleBone Black if used together.

    Learn More
  3. BEAGLEBONE TIWI-5E W/ CHIP ANTENNA

    BEAGLEBONE TIWI-5E W/ CHIP ANTENNA

    $58.95

    Out of stock

    The BeagleBone TiWi-5E Cape w/ Chip Antenna is an add-on board that provides Wi-Fi capability for the BeagleBone. This cape is equipped with LSR TiWi-5E module that is capable of providing high performance 2.4 GHz and 5 GHz IEEE 802.11 a/b/g/n. The TiWi-5E chip use on this cape is based on the Texas Instrument WL1273L chipset. This cape has on-board antenna.

    Note: Hardware incompatible and will damage BeagleBone Black if used together.

    Learn More
  4. BEAGLEBONE TIWI-BLE CAPE W/ EXTERNAL ANTENNA

    BEAGLEBONE TIWI-BLE CAPE W/ EXTERNAL ANTENNA

    $68.95

    Out of stock

    BeagleBone TiWi-BLE Cape w/ External Antenna is an add-on board that provides Wi-Fi capability for the BeagleBone. This cape is equipped with LSR TiWi-BLE module that is capable of providing high performance 2.4 GHz IEEE 802.11 b/g/n. The TiWi-BLE chip use on this cape is based on the Texas Instrument WL1271L chipset. This cape uses an external antenna that is shipped with the unit.

    Note: Hardware incompatible and will damage BeagleBone Black if used together.

    Learn More
  5. BEAGLEBONE TIWI-BLE W/ CHIP ANTENNA

    BEAGLEBONE TIWI-BLE W/ CHIP ANTENNA

    $58.95



    The BeagleBone TiWi-BLE Cape with Chip Antenna is an add-on board that provides Wi-Fi capability for the BeagleBone. This cape is equipped with LSR TiWi-BLE module that is capable of providing high performance 2.4 GHz IEEE 802.11 b/g/n. The TiWi-BLE chip use on this cape is based on the Texas Instrument WL1271L chipset.

    Note: Hardware incompatible and will damage BeagleBone Black if used together.

    Learn More
  6. BEAGLEBONE 3.1MP CAMERA CAPE

    BEAGLEBONE 3.1MP CAMERA CAPE

    $78.95

    Out of stock

    The BeagleBone Camera 3.1MP Cape provides a portable camera solution for BeagleBone boards. This cape features a 3.1-megapixel camera which interfaces to BeagleBone via GPMC. In addition to a power indicator, the BeagleBone Camera Cape is also equipped with EEPROM for cape identification and pin muxing configuration.

    Note: BeagleBone 3.1MP Camera Cape should be used with LCD7 Cape or DVI-D Cape for previewing and capturing photos.

    Note: This cape is functional with BeagleBone Black but requires boot from SD card.

    Learn More
  7. AUDIO CAPE

    AUDIO CAPE

    $29.99

    Out of stock

    The Audio Cape is the new version of the BeagleBone Audio Cape. This cape features TLV320AIC3104 codec and provides stereo input and output via two standard 3.5mm audio jacks. Audio data are transferred via the audio serial bus.

    Learn More
  8. RS-232 CAPE

    RS-232 CAPE

    $29.99

    Out of stock

    The RS-232 Cape is the new version of the BeagleBone RS232 Cape. This cape provides RS-232 interfaces via a standard D-Sub 9 serial connector. Users will have access to UART0 (the console), UART1, UART2, and UART4.

    Learn More
  9. BEAGLEBONE WL1835MOD W/ CHIP ANTENNA

    BEAGLEBONE WL1835MOD W/ CHIP ANTENNA

    $47.95

    Out of stock

    The BeagleBone WL1835MOD W/ CHIP ANTENNA is an add-on board that provides Wi-Fi and Bluetooth® capability for the BeagleBone. This cape is equipped with Texas Instrument’s WL835MOD pre-certified module. It offers advanced WiFi features including 2.4-GHz MRC Support for Extended Range, 2x2 MIMO and 40-MHz Channels for High Throughput, Wi-Fi Direct Concurrent Operation (Multi-Channel, Multi-Role) and SmartConfig technology. It also supports Bluetooth 4.0 including Bluetooth and BLE and Built-In coexistence technology for Bluetooth-BLE and WLAN. A Royalty-Free Certified Bluetooth Stack From StoneStreet One is also available from TI. This cape has on-board antenna.

    The WL1835MOD w/ Chip Antenna is being sold as a development/evaluation module for the Wilink8 module. It is originally designed to work with the BeagleBone (White) using Texas Instruments SDK for 3.2 kernel. There is also a guide on Texas Instrument wiki on using this cape with BeagleBone Black. For any software support please contact TI.

    Learn More
  10. BEAGLEBONE WEATHER CAPE

    BEAGLEBONE WEATHER CAPE

    $68.95

    Out of stock

    The BeagleBone Weather Cape provides weather data for the BeagleBone including temperature, barometric pressure, humidity, and ambient light. These weather input data can be accessed via I2C bus. The BeagleBone Weather Cape also features an LED to indicate that power is applied.

    Note: Only revision B is fully compatible with BeagleBone Black. Revision A needs a work around. See below for more details.

    Learn More

   

Set Ascending Direction
per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4