Shopping cart - Cart Subtotal:$0.00

 
 
 

BeagleBone Capes

The capes listed below are compatible with BeagleBone (White).

   

Set Ascending Direction
per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4
  1. BEAGLEBONE RS485 CAPE

    BEAGLEBONE RS485 CAPE

    $38.95

    Out of stock

    The BeagleBone RS485 Cape provides an RS485 interface to the BeagleBone via a standard D-Sub 9 female serial connector. This connector is located to the side so it doesn't interfere with any capes stacked above it. Users will have the freedom of selecting four different UART interfaces via jumpers.

    Note: There's currently no software support for BeagleBone RS485 Cape. This cape is sold for development purposes only.

    Note: Not Compatible with BeagleBone Black.

    Learn More
  2. BEAGLEBONE RF CAPE

    BEAGLEBONE RF CAPE

    $58.95



    The BeagleBone RF Cape provides BeagleBone boards the ability to interface with different radio technologies. This cape features industry standard radio EVM connectors which can be used to interface with two simultaneous radio devices.  The BeagleBone RF Cape has been tested on Texas Instruments' CC1101 modules. Other CC series may be compatible but haven't been tested. Please visit this link for a list of CC1101 modules.

    Note: The BeagleBone RF Cape is provided with NO software support. If you have any issue related to hardware please request an RMA here.

    Learn More
  3. BEAGLEBONE MEMORY EXPANSION CAPE

    BEAGLEBONE MEMORY EXPANSION CAPE

    $34.95



    The BeagleBone Memory Expansion Cape provides BeagleBone the capability to add additional external memory devices. The External memory devices are interfaced via general purpose memory controller (GPMC) on the AM335x. Supported memory devices include NOR flash, NAND flash, or other memory devices that are asynchronous, synchronous, 8-bit or 16-bit.

    Note: Not Compatible with BeagleBone Black.

    Learn More
  4. BEAGLEBONE BEBOPR CAPE

    BEAGLEBONE BEBOPR CAPE

    $89.99



    The BeBoPr Cape provides all the necessary I/O to control a Mendel/Reprap 3D-printer. All 'hard' realtime control, e.g. step pulse generation, acceleration etc. runs on a dedicated coprocessor that is part of the AM3359 on the BeagleBone. The 'soft' realtime control, e.g. traject planning, temperature control etc., runs on the ARM processor under Linux.

    A license for the coprocessor code comes with the board. A port/rewrite of the RepRap/Teacup 3D printer control software is expected to be ready before end Q2/2012. All Linux code will be Open Source, the coprocessor code will be provided as a binary module.

    Note: This board is sold AS-IS. No support will be provided from the seller or manufacturer. For any support, please visit GitHub or contact the designer bebopr@aeselectronics.nl.

    Learn More
  5. Battery Cape - Angled View

    BEAGLEBONE BATTERY CAPE

    $48.95

    Out of stock

    The BeagleBone Battery Cape provides a portable power solution for BeagleBone boards and its Capes. This Cape provides 5V power supply to the BeagleBone using 4 Lithium AA battery cells. Power will be provided to BeagleBone’s VDD_5V power rail as soon as battery cells are installed. The BeagleBone Battery cape is also equipped with a power switch, a power indicator LED, and an EEPROM for muxing configuration.

    Note: Batteries are not included.

    Note: Compatible With both BeagleBone and BeagleBone Black.

    Learn More
  6. BEAGLEBONE BREADBOARD

    BEAGLEBONE BREADBOARD

    $29.95

    Out of stock

    The BeagleBone Breadboard is designed to provide a simple but productive prototyping space. This prototyping cape is equipped with a patterned prototyping area, two general LED’s, two tactile switches, one 8-pin female header and two stackable 46-pin connectors. LED’s and switches are wired to an 8-pin header for convenient access. There are cutbacks for the Ethernet connector as well as LED’s and reset button on the BeagleBone board. The 46-pin headers are stackable so users won’t have to worry about losing this feature. With each purchase including an adhesive solderless breadboard and jumper wire kit (140 pieces in 14 different lengths), the BeagleBone Breadboard offers users a powerful prototyping tool without the needs of soldering.

    Note: Compatible with both BeagleBone and BeagleBone Black

    Learn More
  7. BEAGLEBONE BREAKOUT CAPE

    BEAGLEBONE BREAKOUT CAPE

    $39.95



    The BeagleBone Breakout provides easy access to the BeagleBone components and test points during troubleshooting processes. BeagleBone’s are great with its stackability. However, when it comes to troubleshooting, access to some test points and components on the top side of BeagleBone and bottom side of the stacking capes are very limited. The BeagleBone Breakout cape solves this problem by separating BeagleBone and its cape. There are two cutouts on the breakout cape, and each cutout is equipped with a set of two 46-pin connectors. One connector set is for the BeagleBone board, whereas the other is for its capes.

    Note: Compatible with both BeagleBone and BeagleBone Black

    Learn More
  8. BEAGLEBONE CANBUS CAPE

    BEAGLEBONE CANBUS CAPE

    $58.95

    Out of stock

    The BeagleBone CANBus Cape makes use of DCAN1 interface of the AM335x processor. The CAN Bus interface can be accessed via a standard D-Sub 9 female serial connector. This connector is located to the side so it doesn't interfere with any Capes stacked above it. The BeagleBone CANBus Cape will support SocketCAN.

    Note: Not compatible with BeagleBone Black.

    Learn More
  9. BEAGLEBONE LCD3 CAPE

    BEAGLEBONE LCD3 CAPE

    $69.95

    Out of stock

    The BeagleBone LCD3 Cape provides a portable LCD solution with touchscreen capability for BeagleBone boards. The 3.5" TFT LCD screen, attached to the topside of the board, can display up to a resolution of 320x240 and is a 4-wire resistive touchscreen. The board is equipped with seven switches located at finger-friendly positions. These switches include power, reset, and five user switches, which are mapped to different GPIO signals. The backside of the Cape is where a BeagleBone can be mounted.

    Note: Compatible with BeagleBone Black (RevA2 or newer is fully supported)

    Learn More
  10. BEAGLEBONE LCD4 CAPE

    BEAGLEBONE LCD4 CAPE

    $88.95

    Out of stock

    The BeagleBone LCD4 Cape provides a portable LCD solution with touchscreen capability for BeagleBone boards. The 4.3" TFT LCD screen, attached to the topside of the board, can display up to a resolution of 480x272 and is a 4-wire resistive touchscreen. The board is equipped with seven buttons located at finger-friendly positions. These buttons include power, reset, and five user buttons, which are mapped to different GPIO signals. The backside of the cape is where a BeagleBone can be mounted.

    Note: Compatible with BeagleBone Black ( RevA1 or newer is fully supported)

    Learn More

   

Set Ascending Direction
per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4