Shopping cart - Cart Subtotal:$0.00

 
 
 

BeagleBone Black Capes

The capes listed below are compatible with BeagleBone Black.

   

Set Ascending Direction
per page
Page:
  1. 1
  2. 2
  3. 3
  1. RIGHT ANGLE SERIAL ADAPTER

    RIGHT ANGLE SERIAL ADAPTER

    $12.95

    Out of stock

    When the BeagleBone Black is used with a cape (add-on board), any cable installed to the serial header J1 on the BeagleBone Black may interfere with the stacking cape. The Right Angle Serial Adapter is used to avoid this interference by converting the vertical serial header on the BeagleBone Black to horizontal. This adapter consists of a right angle through-hole socket and a through-hole header. Both are 6-position and .1" pitch. The connections between the socket and header are 1 to 1. Learn More
  2. BEAGLEBONE 3.1MP CAMERA CAPE

    BEAGLEBONE 3.1MP CAMERA CAPE

    $78.95

    Out of stock

    The BeagleBone Camera 3.1MP Cape provides a portable camera solution for BeagleBone boards. This cape features a 3.1-megapixel camera which interfaces to BeagleBone via GPMC. In addition to a power indicator, the BeagleBone Camera Cape is also equipped with EEPROM for cape identification and pin muxing configuration.

    Note: BeagleBone 3.1MP Camera Cape should be used with LCD7 Cape or DVI-D Cape for previewing and capturing photos.

    Note: This cape is functional with BeagleBone Black but requires boot from SD card.

    Learn More
  3. Battery Cape - Angled View

    BEAGLEBONE BATTERY CAPE

    $48.95

    Out of stock

    The BeagleBone Battery Cape provides a portable power solution for BeagleBone boards and its Capes. This Cape provides 5V power supply to the BeagleBone using 4 Lithium AA battery cells. Power will be provided to BeagleBone’s VDD_5V power rail as soon as battery cells are installed. The BeagleBone Battery cape is also equipped with a power switch, a power indicator LED, and an EEPROM for muxing configuration.

    Note: Batteries are not included.

    Note: Compatible With both BeagleBone and BeagleBone Black.

    Learn More
  4. BEAGLEBONE BREADBOARD

    BEAGLEBONE BREADBOARD

    $29.95

    Out of stock

    The BeagleBone Breadboard is designed to provide a simple but productive prototyping space. This prototyping cape is equipped with a patterned prototyping area, two general LED’s, two tactile switches, one 8-pin female header and two stackable 46-pin connectors. LED’s and switches are wired to an 8-pin header for convenient access. There are cutbacks for the Ethernet connector as well as LED’s and reset button on the BeagleBone board. The 46-pin headers are stackable so users won’t have to worry about losing this feature. With each purchase including an adhesive solderless breadboard and jumper wire kit (140 pieces in 14 different lengths), the BeagleBone Breadboard offers users a powerful prototyping tool without the needs of soldering.

    Note: Compatible with both BeagleBone and BeagleBone Black

    Learn More
  5. BEAGLEBONE BREAKOUT CAPE

    BEAGLEBONE BREAKOUT CAPE

    $39.95



    The BeagleBone Breakout provides easy access to the BeagleBone components and test points during troubleshooting processes. BeagleBone’s are great with its stackability. However, when it comes to troubleshooting, access to some test points and components on the top side of BeagleBone and bottom side of the stacking capes are very limited. The BeagleBone Breakout cape solves this problem by separating BeagleBone and its cape. There are two cutouts on the breakout cape, and each cutout is equipped with a set of two 46-pin connectors. One connector set is for the BeagleBone board, whereas the other is for its capes.

    Note: Compatible with both BeagleBone and BeagleBone Black

    Learn More
  6. BEAGLEBONE LCD3 CAPE

    BEAGLEBONE LCD3 CAPE

    $69.95

    Out of stock

    The BeagleBone LCD3 Cape provides a portable LCD solution with touchscreen capability for BeagleBone boards. The 3.5" TFT LCD screen, attached to the topside of the board, can display up to a resolution of 320x240 and is a 4-wire resistive touchscreen. The board is equipped with seven switches located at finger-friendly positions. These switches include power, reset, and five user switches, which are mapped to different GPIO signals. The backside of the Cape is where a BeagleBone can be mounted.

    Note: Compatible with BeagleBone Black (RevA2 or newer is fully supported)

    Learn More
  7. BEAGLEBONE LCD4 CAPE

    BEAGLEBONE LCD4 CAPE

    $88.95

    Out of stock

    The BeagleBone LCD4 Cape provides a portable LCD solution with touchscreen capability for BeagleBone boards. The 4.3" TFT LCD screen, attached to the topside of the board, can display up to a resolution of 480x272 and is a 4-wire resistive touchscreen. The board is equipped with seven buttons located at finger-friendly positions. These buttons include power, reset, and five user buttons, which are mapped to different GPIO signals. The backside of the cape is where a BeagleBone can be mounted.

    Note: Compatible with BeagleBone Black ( RevA1 or newer is fully supported)

    Learn More
  8. BEAGLEBONE LCD7 CAPE

    BEAGLEBONE LCD7 CAPE

    $157.95



    The BeagleBone LCD7 cape provides an LCD solution with touchscreen capability for BeagleBone boards. The 7" TFT LCD screen, attached to the topside of the board, can display up to a resolution of 800x480 and is a 4-wire resistive touchscreen. The board is equipped with seven buttons located at finger-friendly positions. These buttons include five user buttons that are connected to GPIO signals as well as power and reset. The backside of the cape is where the BeagleBone and additional cape can be mounted.

    Note: Compatible with BeagleBone Black (RevA2 only supports booting from microSD card, RevA3 or newer is fully supported when using Angstrom release 2013-06-20 or newer). Please visit the Software Support section on the wiki page for more details.

    Learn More
  9. AUDIO CAPE

    AUDIO CAPE

    $29.99

    Out of stock

    The Audio Cape is the new version of the BeagleBone Audio Cape. This cape features TLV320AIC3104 codec and provides stereo input and output via two standard 3.5mm audio jacks. Audio data are transferred via the audio serial bus.

    Learn More
  10. RS-232 CAPE

    RS-232 CAPE

    $29.99

    Out of stock

    The RS-232 Cape is the new version of the BeagleBone RS232 Cape. This cape provides RS-232 interfaces via a standard D-Sub 9 serial connector. Users will have access to UART0 (the console), UART1, UART2, and UART4.

    Learn More

   

Set Ascending Direction
per page
Page:
  1. 1
  2. 2
  3. 3